Accessories to Flame Photometer FF-200
Cole-Parmer Instrument
CHF 2,604.00*
Content:
1
Delivery according to order confirmation
Product number:
6281378
Manufacturer:
Cole-Parmer Instrument
Packaging information:
Length:
276 mm
Width:
251 mm
Height:
205 mm
Weight:
0.8 kg
Description
Please Note: These products will only operate with the correct type of air compressor and gas regulator as specified below.
Properties
| Description: | Minor spares kit |
|---|---|
| Manufacturer Article Number: | 99960-11 |
Skip product gallery
Standards for Flame photometers
From
CHF 58.40*
Flame Photometers FP8000 series
From
CHF 89,378.13*
Flame Photometer FF-200
From
CHF 6,742.00*
Similar products
Suitable for calibration, control, IQ / OQ and method validation. Compatible with all Flame Photometry Instruments. Available as single element analytical standards (in ppm) or Multi-element clinical standards (in mmol/l). NIST traceable. HDPE bottles of 500 ml.
Even the lowest concentrations of alkali and alkaline earth elements in aqueous solutions can be determined cost-effectively and user-friendly. Simultaneous measurement of the elements Na, K, Ca and Li in the laboratory and process analysis (others on request). Thanks to proven measuring methods and modern instrument electronics, the flame photometers achieve precise and reproducible measurement results in a matter of seconds with maximum operational reliability. Suitable for individual measurements, fully automatic measuring operation, continuous operation and use as a process instrument.Economic, user-friendly and durable solution for use in laboratory and process operationSimultaneous measurement of up to four alkaline and alkaline earth elements, depending on model up to 300 measurements per hourMaximum operational safety through intelligent security mechanismsSimple operation through touch screen and intuitive softwareTo use with Popan/Butan (alkaline elements) and Acetylene (alkaline earth elements)Interfaces: 2 x USB, 1 x Ethernet, 1 x RS-232 for printer, FP8500 additionally: Upgrade 4 to 20 mA analogue, passive current interfaceCompliance with international norms and standardsSpecificationsMeasuring ranges:
Na/K/Li
Ca
0,01 ... 4500 ppm
0,50 ... 4500 ppmCalibration:Linear with 2 standards
Not-linear with 6-8 standards, cubic approximationDrift:1 % in 60 minReference:Lithium guideline with 5 mmol/l
Cäsium guideline on request
Single channel, low temperature flame photometer for use in industry, medicine and education. Can be operated with propane, butane, natural gas or liquid gas (LPG). With built-in electronic flame failure safety system for operational safety.Model FF-200D-I incl. Na, K, Ca, Ba and Li filtersModel FF-200D-R incl. Na, K and Li filters3 year warrantySupplied with: Na, K, Li filters (model FF-200D-R), additionally Ba and Ca filter (model FF-200D-I), connecting hoses and clips, compressor plug, drain trap, fuses and operating/service instructionsSpecificationsRange FF-200D-I:
Range FF-200D-R:
Limits of detection
Na/K:
Li:
Ca:
Ba:0 ... 199.9 ppm
120 ... 160 ppm Na, 0 ... 10 ppm K
0.2 ppm
0.25 ppm
15 ppm
30 ppmReproducibility: 1 % (Coefficient of variation for 20 consecutive samples using 10 ppm Na set to a reading of 50)Linearity: 2 % (when concentration of 3 ppm Na/K and 5 ppm Li are set to a reading of 100)Specificity:Interference from Na, K and Li equal in concentration to test element will be 0.5 %Recorder output:Nominal 1.00 V for a reading of 100.0Air:6 l/min at 1 Kg/cm2 /14psi (oil and moisture free pressurised air)Dimensions (W x D x H):
Weight:420 x 360 x 300 mm
8 kgPower supply:190 ... 250 V, 50/60 Hz